1 month by cncdivi
Note: This is Lesson 18 of our Free Email Feeds & Speeds Master Class. Click here to learn more about the Master Class.
Whether you call it Deep Pocket, Deep Cavity, or Deep Slot Milling, dealing with extended reach situations is one of the hardest problems in machining. Using long or extended reach tools to reach down into a deep pocket situation leads to problems with:
- Tool Deflection
- Machining Chatter
- Wall Taper
- Wall Finish
- Coolant Delivery
- Chip Extraction
- Recutting Chips
All this adds up to poor tool life, breakage, and longer cycle times. Couple all that with thin walls and you have this part Eric Tate recently showed on the Yahoo Tormach forums:
Deep pocket of 3.125″, endmill of 3/8″, and thin walls as well!
With a part like that, if the tool doesn’t chatter from the long reach the thin walls will chatter.
Tate reports taking 0.030″ depth of cut passes and 600 rpm were the secret, discovered after some trial and error experimentation and a broken endmill.
Techniques for Deep Pocket Milling
How can we make Deep Pocket Milling more of a science and less trial and error?
The answer is to use proven techniques to proactively address the challenges of Deep Pocket Milling that we know are there. Let’s go over the different techniques that are available to address these issues.
Here’s my CNC Chef video from Cutting Tool Engineering magazine to provide a quick intro to Deep Pocket and Deep Slot Milling:
The rest of the article gives you an even deeper dive on these techniques including Trochoidal Milling and Plunge Milling.
Tool Deflection for Deep Cavities and Long Reach Situations
Tool Deflection happens when sideways cutting forces bend the tool. The further the tool sticks out and the smaller its diameter, the more a given force can bend the tool. Think of tool deflection as being addition to chipload, and similar to runout in its effect on tool life. Way too much and the tool snaps immediately. A little too much and the tool’s life is reduced exponentially. Here’s a graph showing the effect:
The graph is for runout as a percentage of the allowable chipload vs tool life. As I mentioned, deflection behaves just like runout. So, if we allow deflection to reach 50% of chipload, our tool life will only be 60% of normal.
In addition, excessive deflection can lead to chatter as well as wall taper, poor wall finish, and generally poor tolerances.
Not what we want, but how do we fix it.
The first thing is to minimize tool stickout while maximizing tool diameter. Of course this article is about Deep Pockets, which are only deep in comparison to their tight corners. So, large tool diameters and short stickouts are probably not available to us.
The next thing is to be aware of deflection. How much is there for a given cut?
This requires that we use a feeds and speeds calculator capable of predicting Tool Deflection, like our G-Wizard Calculator. Once we know how much deflection there is, we stand a chance of optimizing our cutting parameters to minimize it. G-Wizard has a couple of tools to assist with this.
G-Wizard’s Cut Optimizer makes it easy to calculate the optimal Cut Depth or Cut Width needed to keep Tool Deflection under control. It’s CADCAM Wizards will optimize both Cut Depth and Cut Width to avoid deflection right up front.
But G-Wizard’s best feature for dealing with Deep Pockets is the ability to fine tune exactly what the right amount of deflection should be for your cut.
Deflection Limits for Deep Cavity Machining
If you’re going for broke on your Material Removal Rates or you are having to deal with deep pockets that won’t accommodate large enough tools, you need to consider more aggressive strategies. You could just forge ahead and choose to deal with chatter if it comes up. That being the case, you can probably tolerate a higher deflection limit. G-Wizard provides a means to change that limit on the Setup Other tab:
You can override G-Wizard’s Deflection Limit on the Setup Other tab…
Here’s what the options do:
- Limit Chatter: Chooses a very conservative deflection limit that helps avoid chatter. This is the default.
- Best Finish: Chooses a much lower limit if you are in the Finish (non-Roughing) portion of the Tortoise-Hare slider. This helps reduce tooling marks in the wall of the cut for better surface finish. This is OFF by default.
- Deflection Limit: If you turn off “Limit Chatter”, this area is enabled. It lets you set a Deflection Limit that is a percentage of maximum chipload. It also tells you the impact on Tool Life. For example, at 20% of max chipload, Tool Life is 92% of normal.
If you’re in a tough situation and need a higher deflection limit, turn of Limit Chatter and dial up the Deflection Limit until you hit a Tool Life value that is as low as you can stand.
If your shop is fortunate enough to be taking a scientific approach to chatter, you can probably quit worrying about chatter when choosing your deflection limits. Chatter is highly repeatable and largely depends on just four variables:
- Machine
- Tool Holder (not the exact holder, just the same brand and model)
- Tool (again, just the same brand and model)
- Stickout
That’s a manageable number of variables, and if you know the chatter danger zone in terms of spindle rpm for those variables most of the time, you’ll know whether chatter is even an issue for the Feeds and Speeds you’re contemplating.
One last hint: try using roughing end mills with serrated edges. They generate a little less cutting pressure if all else is equal, and so will develop less tool deflection.
Relieved and Tapered Tool Shanks for Deep Pockets
Deep Pocket machining will amost always require multiple stepdown passes to reach the bottom of the cavity. The worse the tool deflection issues, the more passes will be required.
If you’ve got flutes the full length of the tool, they’re going to be rubbing and potentially cutting the walls created by previous passes. That needs to be minimized, and the right way to do that is to use tool shanks that have been relieved so they don’t contact the wall. That coupled with flute length that is just long enough for your actual cutting needs (i.e. the height of a single pass) does the trick.
Keeping flute length shorter also means less deflection because you’ve got more meat in the cross-section to resist deflection.
Coolant Solutions for Deep Pockets and Deep Slots
With Tool Deflection under control and Relieved Shanks to keep our walls clean, the next issue to consider is coolant. It’s hard to get coolant down into Deep Cavities and it’s harder for that coolant to extract the chips. Premium coolant solutions such as Through Spindle Coolant, High Pressure Coolant, and Programmable Coolant Nozzles can be a great help, and G-Wizard can adjust your feeds and speeds accordingly to take advantage.
If premium coolant options are not available, carefully aiming the coolant nozzles to best effect is the alternative. It will make a very noticeable difference if the machine operator does this.
Using Multiple Tools for Deep Pockets, Slots, and Cavities
If your machine has a fast tool change and available pockets in the changer, you may be able to perform Deep Pocket Milling more quickly by using multiple tools. The idea is to use more than one stickout. The shorter stickout tools are used for the initial passes. They can cut a deeper initial pass because they’re more rigid. When you run out of clearance, perform a tool change for a longer reach tool.
Trochoidal Milling and HSM for Deep Slots and Deep Cavities
Trochoidal Milling is a High Speed Machining (HSM) technique that moves the tool in a shape called a “Trochoid.” The link shows the derivation of what a Trochoid is, but here’s a typical Trochoidal Toolpath:
Using Trochoidal Milling to cut a slot…
The idea is each cut is a circular arc rather than moving down the slot in a straight line. The advantage of Trochoidal Milling is it keeps a constant load on the cutter so you can run higher feeds and speeds. Some Trochoidal paths create a more “D” shaped toolpath and don’t do a complete circle each time, which can be faster than the full circles. Trochoidal and HSM paths are also good for Deep Cavity and Deep Slot operations.
Check our article on Trochoidal Milling for more information.
Plunge Milling for Low Rigidity Situations
Plunge Milling (also called Plunge Roughing) is another toolpath that’s well suited to situations where rigidity is a challenge. The idea, is to rough out a pocket, profile, or 3D surface by plunging either a twist drill, an endmill, or a special-purpose tool straight down into the material. Here’s a typical example:
Plunge Milling a Pocket – Image courtesy of BobCAD…
The graphic shows a typical plunge milling operation for a square pocket, courtesy of BobCAD. As you can see, a chain of holes are plunged vertically with the tool to rough out most of the pocket area. A subsequent finish pass will complete the pocket.
The advantage of plunge milling for Deep Cavity work is that most of the cutting forces are along the Z-axis rather than perpendicular to the diameter of the cutter. That means much higher rigidity and lower tool deflection.
See our article on Plunge Milling for details.
Corner Drilling for Deep Pockets
It’s often a good idea to use two different tool diameters for Deep Pockets:
A larger diameter roughing tool clears most of the material at a higher rate because of its size and rigidity. After, a smaller tool makes a pass that gets into the tight corners to remove the remaining material. With corner drilling, we add a twist drill operation in the corners to remove even more material.
The combination of roughing with a bigger tool and corner drilling means that our smaller finish endmill need not remove much material. Cutting forces and therefore deflection are much less as a result.
See our article on Corner Drilling for more information.
High Feed Milling for Deep Cavities
Like plunge milling, high feed milling concentrates most of the cutting forces along the Z-axis. So it can be advantageous for Deep Pocket situations.
Like what you read on CNCCookbook?
Join 100,000+ CNC'ers! Get our latest blog posts delivered straight to your email inbox once a week for free. Plus, we’ll give you access to some great CNC reference materials including:
- Our Big List of over 200 CNC Tips and Techniques
- Our Free GCode Programming Basics Course
- And more!
Just enter your name and email address below:
100% Privacy: We will never Spam you!
![Bob Warfield](https://www.cnccookbook.com/wp-content/uploads/2023/01/SeatedArmsCrossedSmile-scaled.jpg)
Bob is responsible for the development and implementation of the popular G-Wizard CNC Software. Bob is also the founder of CNCCookbook, the largest CNC-related blog on the Internet.